I didn’t want to see the excess lattice under the planters, so I used a cordless circular saw to cut the excess from the bottom. Then I laid the lattice down on top of the constructed frame and secured it with 1-inch brad nails. I measured, marked, and cut the 1×4 boards to length and constructed the frame with pocket holes. I don’t usually like to use pressure-treated lumber, especially for a vegetable garden, but these boards won’t really come into contact with my plants so I wasn’t too worried about it. Now that the planter is complete, I moved onto building the trellis. Then, I attached the trim with wood glue and brad nails. I usually cut the boards long and then shave off a little at a time until the miter joints are tight. It’s best to “sneak up on the cut” here so that you get the tightest fit. To add the trim, I ripped a couple of pickets down to 1 1/2 inches wide, then measured and mitered the ends at 45 degrees. Then, I simply laid the slats on top of the cleats, spacing them out evenly. I placed the cleats about 12 inches down from the top of the planter. I’m no gardening expert, but I believe a good rule of thumb is to have at least 8 inches of soil for your plants (although don’t quote me on that). You can place the cleats at any height in the planter. Next, we attached the cleats to the inside of the planter box – this will support the bottom slats. Secure at each corner with 1 1/4-inch brad nails and wood glue. Once all four panels are constructed, they should come together like a puzzle. There will also be a 5/8-inch inset on both ends. Lay the legs and rails in position, then attach the planks with 1-inch brad nails and wood glue. Construct the side panels in the same way you did the front and back panels. However, this time, you’ll rip the legs down to 2 7/8 inches. Once again, rip the rails down to 3 1/2 inches. Set that aside and move onto building the side panels.Ĭut the legs, short rails, and planks to length. Repeat and build two of these panels – these will be the front and back panels of the planter. ![]() Then I used my brad nailer to attach the planks with 1-inch brad nails and wood glue. I laid the legs and rails down on my workbench, with the smooth side facing down, then positioned the planks on top of them, leaving a 5/8-inch inset on each end. If this is the case, lay the good side down so that the rough side will be on the inside of the planter. ![]() Sometimes cedar fence pickets can have a smooth side and a rough side. The planks will remain at the original 5 1/2-inch width. Then I ran the leg and rail parts through the table saw, ripping them down to 3 1/2 inches wide. Using cedar fence pickets helps to keep the costs down – one fence picket is about $3/board and cedar is a good choice for exterior applications because it’s naturally resistant to rot and pests.įirst, I cut the legs, long rails, and planks down to length on the miter saw. It made building these raised planters fast and easy. I was excited to give my new pneumatic brad nailer a try – I’m happy to report it’s lightweight and easy to operate. ![]() Arrow Fastener T50ACD Compact Electric Staple Gun + staples.How To Make A DIY Raised Planter with Trellis TOOLS: This is a great weekend project that will cost around $50-$75 in materials (for one planter). As always, I’ve got the PDF plans available for you to download below. The Arrow Pneumatic Brad Nailer and Compact Electric Stapler made this build fast and easy. I’m thrilled to be partnering with Arrow Fastener on this DIY raised planter with trellis project. It’s my happiest place! This planter was so easy and affordable to make, I made two of them! Read on if you want to make your own. Don’t they look great against the Woodhouse Workshop? It’s the cutest little workshop that ever was and the planters add so much charm and functionality. It’s Fall planting season, friends! We are so excited to get some fall veggies planted in our brand new DIY raised planters with trellis. An easy, step-by-step tutorial on how to make a DIY Raised Planter with Trellis for about $50! Includes a tools and supply list with photos and downloadable PDF plans!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |